Bookmark This Site Silver Bullet Enterprises AC DC Dual Power Colloidal Silver Generator Instructions

 

Silver Bullet Enterprises

Producers of Safe, Simple and Economical

Colloidal Silver Generators

and related Products... 

3620 W. 10th St. #180 

Greeley, Colorado 80634

Phone: 720-544-7023         e-mail: sales@silverbulletenterprises.com

 

AC/DC Colloidal Silver Generator INSTRUCTIONS

Part I:

Simple Instructions for Making Your Own Colloidal Silver, Using Your AC/DC Home Colloidal Silver Generator...

Note: It is vital that you read these instructions carefully before attempting to make your first batch of colloidal silver! Be extra sure to carefully read the important WARNINGS in Steps #7 and #9, and in Tip #6, below.

Your brand new AC/DC Home Colloidal Silver Generator Kit contains the following:

Note: To make a high-quality colloidal silver supplement, you MUST use distilled water, available at most large grocery stores or supermarkets for about $1.00 a gallon or less. Keep your distilled water at room temperature. Do not refrigerate.

Step 1.) Fill the small dropper bottle up to the bottom of the neck with distilled water.

Step 2.) Crush about1 teaspoon of sea salt and add it to the water in your dropper bottle. Close the lid and shake well to make sure the sea salt is dissolved in the water. This is your saline solution.

Step 3.) Fill a 16-oz. glass tumbler with distilled water. (A large drinking glass will do -- do not use a metal container, as metal will short-circuit the silver-making process.)

Step 4.) Use the dropper from your dropper bottle to add four drops of saline solution into the water in your 16-oz. glass tumbler. (If you are using a smaller glass tumbler, simply add one drop of saline solution for each 4 oz. of water in your tumbler.)

Step 5.) Make sure that each of your two six-inch lengths of .9999 fine silver rods are slightly bent about one-half inch from the top, so you can hang them over the edge of your 16-oz. glass container, and into the water. Next, insert each of your silver rods into the water in your glass container so that the bent ends are hooked over the outside edge of the container, and the remaining lengths of silver rods are submerged in the water. Position the two silver rods about an inch apart so that they do not touch each other while dangled in the water.

Step 6.) Pick up the two alligator clips that are attached to your generator box, and briefly touch them together, watching how brightly the little green bulb on the generator box glows. The glowing bulb indicates that the batteries in your generator are strong. (If the bulb does not glow, it is likely that your batteries are too weak and need to be changed.)

Step 7.) To use battery power (DC) to run your generator: Take one alligator clip and attach it to the bent end (on the outside of the glass container) of one of the silver rods that you have hooked over the rim of your glass container. Then, attach the second alligator clip to the bent end (on the outside of the glass container) of the second silver rods you have hooked over the rim of your glass container. Once you have attached the alligator clips to the tips of the two silver rods, the process will automatically begin.

If you prefer to use 110/115 volt household AC current instead of battery power, simply hook up the alligator clips exactly as above, and then plug the unit into the wall. ALWAYS PLUG THE UNIT INTO THE WALL AFTER HOOKING UP THE ELECTRODES. The red light will come on, indicating you are now operating on household AC current instead of battery power. Itís that simple! (WARNING: As with any household appliance that plugs into AC current, there is risk of injury or death by electric shock if you place the plugged-in unit where it can fall or be pulled into an open source of water such as a tub, sink, toilet or other. When plugged in, you should never use this unit near an open source of water. Also, when plugged in do not place your unit where your colloidal silver water can be spilled onto it. If the unit falls into water, or water is spilled on or near it when it is plugged in, unplug it immediately. DO NOT REACH INTO THE WATER. Not for use by children. Warn children of risk of death by electric shock.)

Step 8.) IMPORTANT: Be sure you do NOT let the silver rods touch each other while they are in the water. If you do, the colloidal silver-making process will stop. Crossed rods also put the maximum drain on your batteries when using battery power. When using AC household current, crossed rods can, over time, short out your unit. So be sure to keep the silver rods separate at all times. The silver rods should always be at least one or more inches apart while dangled in the water. When using battery power, do not be concerned if the green bulb on your generator box only glows dimly, or even not at all during the process. If you watch carefully, you will observe tiny bubbles of hydrogen rise from one silver rods, while an ultra-fine silver mist begins to come off of the other silver rods. That fine silver mist is the result of millions of microscopic silver ions being driven into the water at once by the electrical charge from the generator. When using a 16 oz. glass tumbler with properly conductive water at room temperature, each minute of activation should produce a silver colloid of approximately 1 part per million (ppm). Ten to twelve minutes of activation should produce a high-quality working solution of about 10 to 12 ppm. Fifteen minutes of activation should produce a high-quality 15 ppm solution. Twenty minutes of activation should produce 20 ppm, etc.

Step 9.) Once the generator has run for 10 to 15 minutes or more (see Step 8 for details on running time), simply unplug the unit if you are using AC household current, and then detach the alligator clips from the silver rods. The process will stop immediately. WARNING: BE ABSOLUTELY SURE THAT YOU HAVE UNPLUGGED YOUR GENERATOR BEFORE TAKING YOUR SILVER RODS OUT OF THE WATER. HANDLING WET SILVER ELECTRODES WHILE THE GENERATOR IS PLUGGED IN CAN RESULT IN A LIGHT (BUT NOTICEABLE) ELECTRICAL SHOCK. If you are using battery power (DC) current, simply detach the alligator clips and the process will stop. Remove your silver rods from the water and dry them with a paper towel or tissue. Usually, one of your silver rods will have a dark oxide film on it after the process is over. Use the small scouring pad provided to clean and polish the darkened rods.

Step 10.) Use the plastic spoon to briefly stir your colloidal silver solution, evenly distributing the light silver mist throughout the water. (Do not use a metal spoon for this. Metal is conductive, and will neutralize the electrical charge held by the silver ions in the solution you have just made. This will cause the silver ions to fall out of solution, and will vastly decrease the potency of your colloidal silver.)

Step 11.) When you have finished making your first batch of colloidal silver, add about 10 or 15 drops of it to the saline solution in your 2 oz. dropper bottle. This will stop fungus growth in your saline solution, and will allow you to store it safely for future use in making more colloidal silver.

Step 12.) When storing your generator, make sure the alligator clips do not touch each other as that will create a circuit that will drain the batteries. To make sure your alligator clips do not touch each other while in storage, you can simply attach them to the small piece of cardboard provided, keeping them about a quarter inch or more apart. Or you can attach them to a thin piece of wood (such as a popsicle stick), or to a thin piece of rubber, to accomplish the same thing.

How to Make "No Salt" Colloidal Silver With Your AC/DC Unit:

Making "no salt" colloidal silver simply requires a substantially longer activation time. Hence it is best to make "no salt" colloidal silver with your generator plugged in to household AC current so you do not run your batteries down. Just follow the simple instructions above, but do not add saline solution to your 16 oz. glass of distilled water.

When making "no salt" colloidal silver, your silver rods MUST be kept parallel, between 3/4" to no more than 1" apart in the water, for best results.

As a general rule-of-thumb, using room temperature distilled water (about 72 degrees), let your generator run for about one hour for each 10 ppm you want. In other words, one hour of running time should give you a good high-quality colloidal silver solution of about 10 ppm...two hours should give you about 20 ppm...three hours should give you about 30 ppm...etc. To achieve the light "golden colored" colloidal silver, three or four hours of running time is necessary, using room temperature distilled water in a 16 oz. glass tumbler. Or, use a six or eight ounce glass tumbler and let your generator run two hours or more, until the light golden color is achieved.

Important note: Most people do not realize that when you make colloidal silver without using the saline solution, you usually will not be able to see the colloidal silver ions coming off the silver rods in the form of a silver mist like you can when you use the saline solution as an electrolyte. This is because when there is no saline electrolyte in the water, the microscopic silver ions come off the rods so slowly and in such small numbers that they are generally not visible. Fortunately, there is a simple way to demonstrate that you are producing a colloidal silver solution when you make the "no salt" colloidal silver. You will need one of those little red laser pointers that shine a bright red laser beam ó theyíre available in many catalogs, and at most office supply stores, for about $24 or less. What you do is this: Take your container full of distilled water into a dark room before you start making colloidal silver in it, and shine the red laser pointer downward into the water (being sure you donít shine it into your eyes; laser light shined into the eyes can damage your eye sight). You will see that the red beam of the laser pointer will not show up in the distilled water. This is because there are no minerals or other substances in the water for the little beam of red laser light to reflect off of.

Next, start making your "no salt" colloidal silver solution in the same container of distilled water, being sure to follow the instructions given above. Once you have let the generator run for an hour or more, shine the red laser light downward into the water (again, be sure the room is dark so you can see the beam). This time, because there will be millions of microscopic silver ions in the water, you will be able to see the beam of the red laser shining in the water as it reflects off the silver ions. The stronger the concentration of colloidal silver, the brighter the red laser light beam will show up in the water. In science, this is called the Raleigh-Tyndall effect, and it is precisely how researchers and scientists make sure the colloidal solutions they have prepared without saline electrolyte indeed have suspended colloids in them.

More important info: You need to be aware that when running your generator for the extended periods of time necessary for making "no salt" colloidal silver, a small amount of silver ions will oxidize on the silver rods and eventually begin forming a blackish gunky-looking material on one or both of the rods. It is therefore a good idea to "wipe the rods" at least once in the middle of the generation process, to prevent formation and accumulation of "gunk" in your CS. If any of the gunky-looking material (oxidized silver) comes off the silver rods while you are making colloidal silver, simply wait until you are through making that batch, and then pour it slowly through a paper coffee filter into another container. The paper coffee filter will trap and remove the oxidized silver particles, and will not alter the potency or concentration of your solution. However, preventing the accumulation of the gunky looking stuff, is the preferred method for making high quality colloidal silver.

 

Additional Important Tips:

Tip #1: Keep Your Colloidal Silver Out of Bright Light or Direct Sunlight: Colloidal silver is extremely light sensitive. Your homemade colloidal silver should be stored in a darkly tinted glass bottle, and kept at room temperature in a dark area such as a cupboard. (Tinted glass bottles ranging from 8 to 32 oz. can be ordered inexpensively through almost any good health food store. If you cannot find a darkly tinted glass bottle, simply tape a piece of brown paper bag around the glass bottle you are storing your silver in. Tinted glass prune juice bottles from your local grocery store work well also, as do tinted wine or beer bottles.)

Tip #2: Never store colloidal silver in a metal container. The metal will neutralize the electrical charge held by the silver ions, and ruin the potency of your colloidal silver.

Tip #3: Do not use plastic bottles to store your colloidal silver. Most modern plastics are mixed with metals for stability and tend to magnetize very easily which will cause your ionic silver particles to stick to the sides of the plastic container and lose potency.

Tip #4: Do not refrigerate. As the colloid solution becomes colder, the movement of the electrified silver ion particles will slow down and fall out of solution, severely diminishing the potency. Always shake the bottle before using your stored colloidal silver to be sure the silver colloid is evenly distributed.

Tip #5: Do not store near speaker cabinets, television, radio or other strong magnetic fields. Full potency can be retained for about a month when properly stored.

Tip #6: Where to get Sea Salt. Should you need to purchase more sea salt, you can find it at most health food stores for under $2 per pound. Be sure to use pure sea salt with nothing added (no additives) and nothing removed. A product called "Celtic Sea Salt" is often suggested. Another good product often recommended is De Souzaís Solar Sea Salt. You can order solar sea salt from them directly (and inexpensively) by calling 1-800-373-5171. As an added bonus, De Souzaís Solar Sea Salt is superior to table salt for use in cooking.

Tip #7: Where to get additional .9999 pure silver rods: You can purchase additional strands of 14 gauge ultra-pure .9999 fine silver rod direct from the distribution company at the address below. The price is $18 for each 12 inch strand of silver rod. For a limited time only, you can purchase silver rod in bulk at a significant discount: five feet of .9999 pure silver rod for only $79(thatís only $15.80 per foot), or ten feet of .9999 pure silver rod for only $139 (thatís only $13.90 per foot)! Order online using your Visa , Mastercard, and American Express or Just send your check or money order to:

Silver Bullet Enterprises

3620 W. 10TH St., #180

Greeley, Co. 80634

720-544-7023

Producers of Safe, Simple and Economical Colloidal Silver

Generators and related Products...

 

WE  ACCEPT MONEY ORDERS,  PERSONAL CHECKS,

VISA , MASTERCARD, AMERICAN EXPRESS, or PayPal

USP II GENERATOR (our most versatile)   USP Generator    Silver &Other Products    

Conventional Generators 

Order Form       Literature    Merchandise Disclaimer    Home    Laser Pointer     Links Page

Nebulizer        12vdc to 100vac adapter